幸运飞艇

产品中心

HX2000-2P电梯应急平层装置

一、安装前注意事项
1.1、本说明书适用于输出为二相电源的电梯自动救援装置。
1.2、为了避免造成人员及设备事故,本产品的安装、调试及维修等必须采取以下安全措施:
(1)在进行本产品的安装、连接工作之前,必须将电梯总电源切断。
(2)请确保电梯各设备接地良好。
(3)请按本说明书中提示或警告小心行事,以防对安装或维修人员造成伤害,同时避免
损坏电梯设备。
(4)在接通电源调试之前,必须确保应急电源ARD与电梯电气系统之间连接正确。
(5)本产品的安装、调试等工作应由电梯行业相关技术人员进行,以避免可能发生的危险。
1.3、本说明书介绍了应急电源ARD的安装和连接步骤,信号端子说明,拨码开关说明,调试
和使用、以及出现的故障和排除方法等。
1.4、对电梯自动救援装置的安全操作,必须仔细阅读本说明书,才能防止由于方法不当而造成对人员伤害和电梯系统的损坏。
1.5、请在对电梯进行断电维修前务必关闭应急电源ARD的电源开关,否则有应急电源ARD启
动供电造成伤害的危险。
one、Precautions before installation
1.1、This specification is applied to the output elevator for two-phase power supply automatic rescue device。
1.2、In order to avoid the personnel and the equipment accident, this product installation, debugging and repair, must take the following safety measures.
(1)Before the installation of the products, the work must be connected, 
elevator power cut off.
(2)Please ensure that all the equipment grounding good elevator
(3)Please press this manual prompt or warn caution, to prevent damage to the installation or repair personnel, at the same time, to avoid damaging the elevator equipment
(4)Before switching on the power supply debugging, must ensure that the emergency power ARD and elevator electrical system is properly connected.
(5)The product installation, commissioning work by elevator related technical personnel, in order to avoid the possible dangers.
1.3、This specification describes the ARD emergency power supply connection and installation steps, the signal terminal, dial switch, debugging and use, as well as the problems and their solutions
1.4、The safe operation of the elevator automatic rescue device, must read this manual carefully, in order to prevent the improper methods caused by damage to the injuries and elevator system.
1.5、Please be sure to turn off the power switch of ARD emergency power supply in power before repair on the elevator, or risk of ARD emergency power supply power supply damage.  
二、简介  

   HX814是专为提高电梯的安全性能而设计的电梯安全装置。本装置利用了电梯原有的控制和变频系统、未开发独立于原有电梯控制系统之外的拖动系统,因此他具有安装接线简单、调试方便、性价比高的特点。电梯在使用过程中,一旦遇到供电系统停电,将会对被困在电梯内的乘客造成身体及心理上的伤害。本装置在上述情况发生时,将在设定的时间内自动投入工作,将电梯轿厢往轻载方向缓慢运行到就近站平层、开门,释放乘客。
two、 brief introduction
    HX814 Elevator safety device designed for enhancing the safety performance of elevator design. The device makes use of the drive system of elevator control and frequency conversion system, the original is not developed independently of the original elevator control system, so he has the characteristics of simple wire connection and installation, convenient debugging, high performance price ratio. The elevator is in use process, once in power system blackout, will cause physical and psychological harm to the trapped in the elevator passengers. The device in the above occurs, can automatically work in the given time, the elevator car to light slow run to the nearest station floor, open the door, the release of the passengers.

三、功能特点
3.1、外电网正常情况下,处于待机状态,同时给蓄电池组供电。外电网停电,装置投入工作,当外电网来电时可迅速切换到待机状态。
3.2、外电网停电至装置运行投入工作的时间段可根据实际要求灵活设定。可以解决不同变频器的故障信号消除时间不一致的问题。
3.3、装置的运行时间可灵活设定,有较长时间运行的档位选择。以解决层与层之间因井道过长而使电梯轿厢需要运行较长时间才能运行到平层站的问题。
3.4、本装置的各种输出信号均由程序控制,非常精确,如运行时间等。
3.5、蓄电池组采用的是免加液免维护电池,每隔90天可自动对电池充放电一次。

three、functional characteristics
    3.1、External power grid under normal circumstances, in the standby state, at the same time to battery power supply. External power grid blackouts, device to work, when external power grid calls can quickly switch to the standby stat
3.2、External power grid blackouts to the device working time can be set flexibly according to the actual requirements. Can eliminate the time inconsistency problem to solve the fault signals of different frequency converter.
3.3、The running time of the device can be set flexibly, with long time running gear selection. In order to solve the between layer and layer as well is too long and the elevator car needed to run a long time to run to the floor standing problem.
3.4、A variety of output signals of the device are controlled by program, very precise, such as operation time etc..
3.5、The battery is used in non liquid adding maintenance free battery, every 90 days can be automatically to the battery charge and discharge time.
四、主要技术参数
4.1、输入电压:三相380V(三相400V)±10%,频率50HZ或60HZ。
环境温度:-30℃  ~  40  湿度:30% ~  75%(非凝结)
蓄电池组:48V/12AH
4.2、输出电压:两相AC380V±10%,50HZ正弦波,最大输出电流5A。
4.3、应急电源ARD外形尺寸(长500X宽150X高500、长460X宽150X高430)。
four、Main technical parameters
4.1、Input voltage: three phase 380V (phase 400V) ± 10%, frequency of 50HZ or 60HZ
Environment temperature: -30 ℃ ~40 humidity: 30%~75% (non - condensing)
storage battery:48V/12AH
4.2、Output voltage: two-phase AC380V + 10%,50HZ sine wave, the maximum output current of 5A
4.3、Emergency power supply ARD dimensions(A long 500Xwide 150Xhigh 500、
A long 460Xwide 150Xhigh 430)。
五、安装连接说明
5.1、侦测和短接相序用。

(1)讯号端子排

(请将L24  L25  L26 接入电梯控制柜输入处,停电后L24   L26输出二相380V电压) 
five、Installation instructions
5.1、Detection and short sequence with。
(1)The signal terminals
 
Terminalnumber motherboard wire size function declaration    
1 A7 1 
Run signal, emergency device control system for detection    
2 A8 2     
3 A5 3 
The phase signal, emergency device control system for detection    
4 A6 4     
5 B2 5 
The emergency device stop signal    
6 A4 6   
                             surface 1
(2)Mains input 380V  50HZ


L21  L22 L23 N  
           surface 2
(Please insert the L21 L22 L23 access distribution box open after) 
(3)AC output 380V  50HZ


L24 L25 L26  
            surface 3
(Please insert the L24 L25 L26  access control cabinet of elevator 
input,After the power UW output phase voltage of 380V) 
六、应急装置调试、使用说明
6.1、应急装置与电梯控制柜连接,必须待电梯安装调试全部完毕后,且能投入
正常运行后进行,首先断开电梯控制柜总电源。
6.2、安照表1将应急装置与电梯系统之间的连线接好,切记不能将(L24  L25  L26)接输入,
否则会造成不可修复性损坏。
6.3、.检查接线,确定应急装置与电梯系统之间的接线正确。   
6.4、送上外电网的三相电源,闭合应急电源ARD的控制开关。此时应急电源ARD面板上的
绿色指示灯点亮。表示外电网正常,电池组在自动充电。
6.5、外电网停电时,应急装置将在设定的时间内开始启动投入使用,此时应急电源ARD箱体面板
上的绿色指示灯亮为红色。并输出两组控制信号给电梯系统。在设定的运行时间到平层区,应急电源ARD将自动停止工作,等到外电网来电后自动进入待机状态。
6.6、本装置具有短路、过流、欠压保护功能。
6.7、本装置出场后不需要再进行内部的调试,请在没有本公司技术人员的指导的情况下切勿开
起本装置外壳。如需要对内部进行调整与本公司联系。
six、The emergency device debugging、direction for use
6.1、Emergency device is connected with the elevator control cabinet,Must be the elevator installation and commissioning completed after,And can be put into normal operation after the,First disconnect the power of elevator control cabinet。
6.2、According to table 1 Emergency between the device and the elevator system connection is good,Remember not to(L24  L25  L26)then inputOtherwise it will cause irreparable damage。
6.3、Check wiring,Determine the connection between the emergency device and elevator system correctly。
6.4、The three-phase power grid to send on,Control switch of ARD emergency power supply。The ARD emergency power supply panel on the green indicator lights。Outside the normal operation of the grid,In the automatic charging battery。
6.5、External power failure,The emergency device will start to put into use in the set time,When the green indicator light of ARD emergency power supply box panel on the bright red。And the output of two groups of control signal to the elevator system。To flat floor area at run time,Emergency power supply ARD will automatically stop working,When the automatic standby power after the call。
6.6、The device has the advantages of short circuit、overcurrent、Under voltage protection function。
6.7、The device enters the stage does not need to carry out internal debugging,Please in the absence of the company's technical staff guidance,Do not open the shell of the device。Such as the need to adjust the contact with the company on the inside。
七、维护保养
 HX814电梯应急电源ARD采用的是免加液免维护电池,电池不需要加电解液,每隔90天充电器将对蓄电池进行自动充放电。系统在电池电压过底时会自动保护、切断输出,此时工作指示灯仍为红灯。当应急电源ARD启动时输出一段时间后,自动停止了输出,或一加负载就停止输出,但此时指示灯仍为红灯时,表示电池电量不够,请将电池充饱或更换电池。
seven、tending
 HX814 elevator emergency power supply ARD is free and fluid maintenance free battery,The battery does not need to add electrolyte,Every 90 days the charger will automatically charge and discharge the battery。The system will automatically protect the battery voltage too late、Cut off the output,The indicator light is red。
The output for a period of time when start ARD emergency power supply after,Automatic stop output,Or a load stop output,But the indicator light is red,The battery is not enough,Please charge the battery or battery replacement。

八、规格表
 
额定运转模式 一般标准 电梯往“上”慢速自救运转    
 侦测重载 电梯往“下”慢速自救运转    
交流
输入 电压 系统电压+ - 15%    
 频率 50HZ或60HZ(指定)    



出 电
压 市电正常 试点电压,交流电    
  市电断电 电池供应系统电压+ - 5%,交流电    
 电      流 3A    
 波      形 50/60HZ  正弦波    
电压切换时间 10~30秒   

池 型       式 铅酸免加液免维护专用电池    
 备份时间 5-30分钟(依实际使用负载而定)    
  自救次数 2-4次(间断性停电再来电)    
  充电时间 8小时以上    
LED灯指示 市电正常:绿色 电池供电:红色  
                                 表4
注意:由于各电梯的门机、抱闸等其他设备的功耗不一,实际适应电机功率以
现场为准,用户可以在跟本公司起得联系后增加并联蓄电池组来提高输出电流。
eight、Specifications table
 
Rated operation mode General standard The elevator to the "on" slow rescue operation    
 Detection of heavy The elevator to the "next" slow rescue operation    
AC input voltage system voltage + - 15%    
 frequency 50HZperhaps60HZ(appoint)    
AC output voltage Thenormal electricity The pilot voltage, alternating current    
  Thecity electricity power Battery supply voltage -5%, alternating current    
 current 3A    
 wave form 50/60HZ  sinusoidal wave    
Voltage switching time 10~30 second   

battery type Free lead-acid maintenance free battery with liquid    
 The backup time 5-30 minute(According to the actual load and)    
  Save number 2-4 order(Intermittent power outages and then call)    
  charging interval More than 8 hours    
LEDIndicator light The normal electricity:green battery powered:red  
                                 surface 4
pay attention to:Because the elevator door machine、Power brake and other equipment is not a,Actual adaptation motor power is subject to the scene,Users can contact with the company up after,Increasing the shunt batteries to improve the output current。

友情链接:幸运六合彩官网  幸运六合彩开奖直播  幸运六合彩开奖直播  幸运六合彩  幸运六合彩  幸运六合彩  幸运六合彩官网  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!